- Generates a license for the newest database available in the SW center at the time of activation
- Access to the newest vehicles specs directly from the OEM
- Suitable for all Windows-based wheel aligners from Beissbarth (Easy CCD, ML, KDS, VAS, Easy3D, and Touchless) and Bosch (FWA 4xxx, FWA 64xx, and FWA 9000)
High measuring accuracy and precision for top results
- The combination of the Beissbarth stereo camera measurement system with active reference system and sophisticated software ensures the accurate determination of measured values.
Perfectly integrated into ADAS calibration and head light testing:
- The space in front of the lift can be used for the ADAS calibration jig and head light tester
Highly repeatable initial measurement
- Rolling or driving run-out compensation at ground level
- Three selectable measurement routines: program-driven, quick measurement, choice-free access to single-value check
Sophisticated software for maximum measurement and adjustment efficiency
- Real-time display of measured values combined with vehicle specs
- Visually animated adjustment instructions for third-party vehicles
- Several languages as standard for staff from all over the world
- ASA network ready
Easy and live ride height measurement with easy to attach ride height targets
- Ride height measured automatically
- Ride height measured permanently during alignment
- Automatic adjustment of vehicle specs according to ride height information
- Sensor heads can be easily detached from the lift when not in use to clear up space
- Beissbarth DualView camera system for ultimate control, especially of complex chassis
- No fixed position for targets on the vehicle eliminates room for error
- Plug & play: no calibration required for installation or for exchanging targets
- Extensive Beissbarth vehicle database including alignment helps directly from the OEMs
- Quality Made in Germany
- Cable version
- Sensor head with DualView camera technology
- Target boards
- Ride height markers universal with transportation case
- Ride height markers for Mini / Z3 / Z4
- Vehicle specs database with additional BMW Professional data
- Cabinet
- OEM magnetic clamps with longer magnets
- Lift adapter
- Precision Turntable for front and rear axle
- Remote control
- Brake pedal depressor and steering wheel holder
Please note: the cable set for installation needs to be purchased separately, depending on the lift type
The KDS 3D only allows the use of magnetic clamps. The use of other wheel clamp solutions in combination with the KDS 3D is not approved by the BMW Group.
Version with PC, monitor, printer
| Operating temperature | 5 - 40 °C |
|---|---|
| Electrical connection | 120 - 220 V | 50 - 60 Hz |
| Data transmission type | - corded |
| Measuring system | - 3D |
| Power | 0,5 kW |
| Storage temperature | -20 - 60 °C |
| Relative humidity, use | (40 °C) 10 - 90 % |
| Height cabinet | 1520 mm |
| Width cabinet | 880 mm |
| Depth cabinet | 770 mm |
| Weight cabinet | 100 kg |
| Height sensor head | 130 mm |
| Width sensor head | 320 mm |
| Depth sensor head | 630 mm |
| Weight sensor head | 9,3 kg |
| Operating temperature | 5 - 40 °C |
|---|---|
| Electrical connection | 120 - 220 V | 50 - 60 Hz |
| Data transmission type | - corded |
| Measuring system | - 3D |
| Power | 0,5 kW |
| Storage temperature | -20 - 60 °C |
| Relative humidity, use | (40 °C) 10 - 90 % |
| Height cabinet | 1520 mm |
| Width cabinet | 880 mm |
|---|---|
| Depth cabinet | 770 mm |
| Weight cabinet | 100 kg |
| Height sensor head | 130 mm |
| Width sensor head | 320 mm |
| Depth sensor head | 630 mm |
| Weight sensor head | 9,3 kg |
- Vehicle database update Cars & Vans Europe | Key Card1 690 002 0151 690 002 015
- Ride height markers BMW | KDS 3D models1 690 701 1321 690 701 132
- Only in combination with KDS 3D
- Older Mini, Z3, and Z4 models that require demounting of front fenders for measurement, require special ride height market set (item no. 1 690 701 095)
Advantages:
- Quick mounting and demounting
- Automatic ride height calculation saves time
- Constant control over ride height values during measurement
- Low failure rate
- Special ride height markers BMW | Mini / Z3 / Z41 690 701 0951 690 701 095
Used for automatic ride height measurement on older BMW Mini, Z3, and Z4 models that require demounting of front fenders for measurement
- Replacement adhesive pads for BMW ride height markers | small1 690 701 2361 690 701 236
- Replacement adhesive pads for BMW ride height markers | large1 690 701 2281 690 701 228
- Mechanical aluminum turntable Precision1 690 401 0281 690 401 028
- Very high quality and lifetime in workshop environment
- Steel balls for minimal friction and maximum precision
- Protective rubber cover for aluminum turntable1 690 402 0011 690 402 001
- Additional protection from dirt and liquids
- Drive-on ramps for two aluminum turntables1 690 701 0521 690 701 052
- Drive-on ramps for turntables including connecting piece and drive off protection
- Enables rolling compensation on lifts without embedded turntables
- Drive-on ramps for turntables and sliding plates1 690 401 0081 690 401 008
- Set of Drive-on ramps for turntables and sliding plates
- Suitable for lifts without cutouts for turntables or sliding plates, e.g. MOT lifts
- Lift adapter extension from one to two positions1 690 701 5031 690 701 503
- Extends lift adapter with one position (1690701232) to two positions (1690701231)
- Special lift adapter for Beissbarth / Consul1 690 701 1231 690 701 123
- For attachment of Easy 3D sensor heads on Beissbarth lifts VLH 4245, VLH 4345 and Consul 4-post lifts
- Two positions for sensor heads
- Special lift adapter Extension for Beissbarth / Consul1 690 701 3111 690 701 311
- Extension of two-position adapter 1690701231 for attachment of Easy 3D sensor head on Beissbarth lifts VLH 4245, VLH 4345, and Consul 4-post lifts
- Two positions for sensor heads
- Use only as extension for two-position adapter 1690701231
- Special lift adapter for lifts with U-profile1 690 701 0201 690 701 020
- For attachment of Easy 3D sensor heads on above and in-ground lifts
- One position for sensor heads
- Extension magnet for magnetic holder | 100 mm | 1 pc.1 690 701 5231 690 701 523
One 100mm magnet, three required for a magnetic clamp.
- Target boards 340 cm1 690 701 0321 690 701 032
- Enables measurement of long wheelbases
- Only required for rear axle
- Extension for vehicles with narrow track width or RVs1 690 701 1271 690 701 127
Extension of the measuring boards:
- When used with a very narrow vehicle: use 4x extension
- For motorhomes with a wide body: use 2x extension on rear axle
- Standard target board for Easy 3D1 690 711 0051 690 711 005
- No calibration required before use
- Lightweight and robust
- No exchange required after slight deformation of target
- No fixed position on the vehicle
- Cable set 7.5 m / 7.5 m1 690 701 2051 690 701 205
Cable set for above ground pit solutions
- Cable set 12 m / 12 m1 690 701 0291 690 701 029
Cable set for four post lifts
- Cable set 15 m / 15 m1 690 701 0301 690 701 030
Cable set for scissor lifts
- Cable set 25 m / 25 m1 690 701 1631 690 701 163
Cable set for vertical scissor lifts and special installations
- Brake pedal depressor 1 690 401 0061 690 401 006
- Steering wheel holder 1 690 401 0071 690 401 007
- Step protection for Easy 3D1 690 701 0451 690 701 045
